Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterGate Realignment in Dallas, TX
A sagging or dragging gate usually means one thing: the hinges, posts, or frame have shifted out of alignment, and the gate is now fighting its own weight every time it opens. In Dallas, our clay-heavy soil expands and contracts through wet springs and dry summers, which slowly pushes gate posts out of square. At Carver Gate Repair Dallas, we realign gates so they swing true, latch correctly, and stop wearing out motors and hinges prematurely. This is a focused repair, not a rebuild, and it typically takes one visit. If you’re noticing your gate scraping the ground or the latch no longer lines up, call us at (940) 531-9746 and we’ll send a technician who works exclusively on gates. For a broader look at what we handle, see our Gate Repair page.
When You Need Gate Realignment
Most homeowners don’t notice misalignment until it’s already costing them money in worn parts and they’re searching for Gate Repair Near Me in Dallas, TX. Here are the signs our Dallas customers call about most:
- The gate scrapes or drags along the driveway. This is common in neighborhoods like Lake Highlands and East Dallas, where soil movement tilts posts a few degrees over a few seasons. The scrape marks on concrete are the tell.
- The latch no longer catches on the receiver. If you have to lift or shove the gate to close it, the two sides have drifted. Forcing it just bends the latch arm further.
- The gate drifts open or closed on its own. A gate that swings by itself is out of level and putting constant strain on the hinges and any motor attached to it.
- Hinges are visibly pulling from the post or the gate frame. We see this a lot on older steel tube gates in Preston Hollow, where the hinge bolts wallow out the mounting holes.
- A gate motor is working harder than it used to. A misaligned gate makes a swing operator push against resistance on every cycle. If your FAAC or Viking operator sounds strained, misalignment is often the root cause, and ignoring it shortens motor life.
- The gate leans visibly to one side. Stand back and sight down the top rail. If it’s not level, the post on the hinge side has typically sunk or rotated.
Any one of these is reason enough to have the gate looked at. Left alone, a misaligned gate warps the frame, wears hinge pins oval, and eventually turns a simple realignment into a post replacement job.
Our Gate Realignment Process
We follow the same procedure on every realignment call in Dallas, whether the gate is a single driveway swing in Richardson or a double-leaf steel gate in Coppell. The process is straightforward, and you’ll know the written price before we touch a tool.
- Site inspection and measurement. We check post plumb with a level, measure the gate’s diagonals, and inspect hinge wear, latch alignment, and slab condition. This tells us whether the problem is the post, the hinges, the frame, or a combination.
- Written price before work starts. You get a number on paper for the exact realignment scope. That number doesn’t change at the door. If we find something during the job that changes the picture, we stop and talk to you first.
- Hinge repair or replacement. Worn hinge pins and oblong holes get addressed first. You can’t realign a gate on bad hinges. We weld or re-sleeve as needed, and we match the hinge weight to the gate, not just whatever was there before.
- Post reset or shim correction. If a post has shifted, we expose the base, reset it plumb, and re-secure it. For minor drift, we use shims at the hinge plates to bring the gate back to square without a full post excavation.
- Gate leveling and latch adjustment. We set the gate so it swings freely through its full arc, adjust or replace the latch so it catches without force, and confirm there’s no scrape or drag at any point.
- Motor and operator check (if applicable). For automated gates, we run the operator through multiple cycles to confirm the load is now even, and we check that limit switches and safety sensors work. We train on BFT, FAAC, Linear, and Viking operators, among others, so the realignment doesn’t end with a maladjusted motor.
When we leave, the gate hangs square and swings with one hand. The ground under it stays clean, and every repair carries our written one-year guarantee.
Gate Realignment Pricing in Dallas
In Dallas, a straightforward gate realignment typically runs between $180 and $450, depending on what’s actually out of position (How Much Does Gate Repair Cost in Dallas, TX? (2026 Price Guide)). That range covers most residential driveway and garden gates. Here’s how the cost typically breaks down:
- Simple hinge adjustment and latch realignment: $180 to $280. The gate is slightly off, hinges are still good, and no post work is needed.
- Hinge replacement with gate realignment: $280 to $420. The old hinges are worn or the mounting holes need repair, and we install new hardware sized to the gate.
- Single post reset plus realignment: $400 to $650. The hinge-side post has shifted and needs to be dug out, re-set plumb, and secured before the gate can be re-hung.
- Double gate realignment (both leaves): $500 to $850. Both sides get leveled, hinges checked, and latch/locking hardware aligned as a pair.
What moves the price is the post condition. A gate with good posts is a quick job; a gate with a heaving post is a foundation-level fix. If you have an operator on the gate, we include a motor load check in the realignment, and if the motor itself needs adjustment parts like a limit switch, we quote that separately in writing.
Every realignment quote at Carver Gate Repair Dallas is given before we pick up a wrench, and the price we write is the price you pay. If a repair we make fails within the first year, we come back and fix it at no charge. That’s the 365-Day Done Right Promise, and it’s written into every job.
FAQs – Gate Realignment
Is it cheaper to repair or replace a misaligned gate?
Repairing is almost always cheaper (How Much Does Gate Repair Cost? (2026 Price Guide) - Dallas, TX). A typical realignment in Dallas runs $180 to $450, while a new steel driveway gate installed starts around the cost of a full gate and post package, usually well over that. We’ll tell you plainly if the gate frame is too far gone to be worth realigning, but in most cases the steel and hinges are fine.
How much does gate realignment cost in Dallas?
Expect $180 to $450 for most single driveway gates, and $500 to $850 for a double gate where both posts need leveling. The exact number depends on whether posts have shifted and whether hinges need replacement. Call (940) 531-9746 and we’ll give you a written quote after looking at the gate, free of charge.
Can you fix my gate the same day?
In most cases, yes. If the realignment is hinge- and latch-level work, we can typically handle it in one visit with the parts on the truck. If a post needs to be excavated and re-set, we’ll schedule the work around concrete cure time. Either way, you’ll know the plan and the written price before any work begins.
Does gate realignment help a struggling gate motor?
Yes. A gate that’s out of square puts extra load on the operator on every single cycle, which is why BFT, Viking, and Linear motor systems on misaligned gates burn through boards faster. We test the motor after realigning and, if the operator is still working hard, we quote any motor repair separately.
Call Carver Gate Repair Dallas for Gate Realignment
If your gate is dragging, leaning, or failing to latch, call (940) 531-9746. We answer live, 24 hours a day. We’ll schedule a visit, send a background-checked technician in a marked vehicle, and hand you a written price before any work starts. No moving numbers. No partial fixes. Just a gate that hangs true and a repair covered in writing for a full year.
Written by Lonnie Burke, Owner at Carver Gate Repair Dallas, serving Dallas.