Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterAutomatic Gate Repair in Dallas, TX
Gate Repair services in Dallas typically cost between $185 and $450 for most mechanical and electrical fixes, with motor replacement running $600 to $1,400 depending on the operator brand and swing or slide configuration. Most repairs are completed same-day when the needed parts are on the truck. If your gate won’t open, grinds when it moves, or reverses mid-cycle, the problem is usually a limit switch, loop detector, or worn drive mechanism, and each of those has a specific fix.
Carver Gate Repair Dallas handles automatic gate systems exclusively. We don’t take on fencing, landscaping, or general contracting work. That narrow focus matters when a Viking swing operator starts faulting at 6 a.m. or a FAAC control board loses its programming after a Dallas thunderstorm. Our technicians arrive background-checked and in uniform, diagnose the actual failure, and hand you a written price before turning a single wrench. Call (940) 531-9746 and you’ll speak to a live person, not a voicemail tree. For a broader look at what we do across the city, see our Gate Repair in Dallas page.
Key Takeaways
- Most automatic gate repairs in Dallas run $185 – $450; motor replacement averages $600 – $1,400.
- We work on FAAC, BFT, Linear, and Viking systems, among others, with parts stocked for common failures.
- Every repair carries a written full-year guarantee under the 365-Day Done Right Promise.
- You get a written price before work begins. That number doesn’t move at the door.
- Phones are answered by a live person 24/7, including weekends and holidays.
When You Need Automatic Gate Repair
Electric Gate Repair in Dallas is common because automatic gates take a beating. The clay-heavy soil in neighborhoods like Lake Highlands and Preston Hollow shifts with every wet-dry cycle, pulling posts out of alignment and putting strain on hinges and operators. Summertime heat cooks control boards inside metal enclosures until solder joints crack. None of these failures fix themselves, and most get worse the longer they’re ignored. Here’s what we see most often:
- The gate opens partway and stops. This usually points to a bad limit switch or an obstruction sensing fault. The opener can’t tell where the gate is, so it shuts down mid-travel as a safety default.
- The gate groans, grinds, or shudders while moving. Worn drive gears, dry bearings, or a chain that’s stretched past tension spec. Running it like this accelerates damage to the operator and the gate itself.
- The gate reverses immediately after closing. A failing loop detector, misaligned photo eyes, or a sensitivity setting knocked out of adjustment. In areas like Highland Park where gates sit close to sidewalks, this is also a safety concern for pedestrians.
- The remote or keypad works intermittently. Receiver board issues, corroded antenna connections, or failing capacitors inside the control board. Intermittent means it will fail completely, usually at the worst time.
- The opener hums but nothing moves. A seized motor, sheared drive pin, or capacitor failure. Continued power to a stalled motor burns it out fast.
- Power surge or storm damage. Dallas thunderstorms are hard on exposed control boards. A surge can take out the transformer, main board, or both without any visible damage.
Our Automatic Gate Repair Process
We run service calls on a disciplined sequence so you know exactly what happens from the moment you call. This is what we call The Garrison Standard in practice:
- Call intake and dispatch. You call (940) 531-9746. A live person answers, takes your address, gate type, operator brand if you know it, and the symptoms. We schedule a specific arrival window that same day or the next, depending on how urgent the failure is.
- On-site diagnosis. The technician arrives in uniform, confirms identity, and walks the gate through a full test cycle. That means checking operator response, limit settings, loop detector function, photo eyes, and mechanical wear on hinges, wheels, and the drive assembly.
- Written price before work. You get a written quote detailing the specific repair, the parts needed, and the labor. No verbal estimate that grows later. No “we’ll see once we open it up.” The price you approve is the price you pay.
- Repair with written guarantee. We make the repair, test the gate through full open/close cycles, clean the work area, and confirm operation with you at the gate, not from the truck. Every repair carries a written 365-day guarantee. If the same issue returns within a year, we come back at no charge.
- Warranty documentation. You receive your guarantee in writing before we leave, plus a summary of what was done and what to watch for. If the repair fails inside the year, the second visit is free. No argument, no forms, no fine print tricks.
Automatic Gate Repair Pricing in Dallas
You should know what gate work costs before you call. Here are honest ranges for the Dallas market based on what we bill day to day:
| Repair Type | Typical Cost Range |
|---|---|
| Limit switch replacement | $185 – $260 |
| Loop detector replacement or tuning | $160 – $240 |
| Photo eye repair or realignment | $145 – $220 |
| Drive chain or belt adjustment | $170 – $250 |
| Control board diagnosis and repair | $250 – $450 |
| Motor or full operator replacement | $600 – $1,400 |
| Hinge, wheel, or post realignment | $250 – $500 |
What moves the number within those ranges is the operator brand, the age of the system, and whether parts are locally available or need to be sourced same-day. A Linear board swap is quicker and cheaper than a specialty BFT board. A Viking swing arm with physical damage costs more than a simple limit adjustment. The estimate is always free, always written, and fixed before work starts.
How Much Does Automatic Gate Motor Replacement Cost in Dallas?
Replacing an automatic gate motor or full operator in Dallas typically runs $600 to $1,400. Entry-level slide operators sit at the lower end; heavy-duty swing operators from FAAC or BFT with higher cycle ratings and integrated battery backup land at the top. Labor generally accounts for $250 to $450 of the total, depending on access, existing wiring condition, and whether the old operator has to be cut out. Call (940) 531-9746 for an exact quote on your specific operator, and we’ll give you a written number before any work is scheduled.
What Affects the Cost of Automatic Gate Repair?
Three factors drive How Much Does Gate Repair Cost? (2026 Price Guide) - Dallas, TX. First, the brand and model of operator. BFT and FAAC parts are more expensive than Linear or Viking equivalents, and some control boards have long lead times if not stocked locally. Second, the type of failure. Mechanical repairs like hinge or wheel replacement involve heavier labor than swapping a limit switch or resetting a loop detector. Third, system age. Gates older than 12 to 15 years often have discontinued parts, making retrofit the cheaper path than chasing obsolete components.
FAQs – Automatic Gate Repair
Can you fix my automatic gate today?
In most cases, yes. We dispatch same-day for urgent failures, meaning a gate stuck open, stuck closed, or refusing to respond. The quickest way to confirm is to call (940) 531-9746, and the person who answers will tell you the earliest available arrival window for your neighborhood.
Is it cheaper to repair or replace my automatic gate operator?
Repair is cheaper when the failure is isolated to a single component like a limit switch, loop detector, or capacitor, typically running $145 to $450. Replacement at $600 to $1,400 makes more sense when the motor has seized, the control board is dead, or the operator is over 12 years old and parts are discontinued. We’ll give you both numbers in writing so you can decide with full information.
Do you work on my gate opener brand?
We work on FAAC, BFT, Linear, Viking, LiftMaster, Ghost Controls, DoorKing, Elite, and Mighty Mule. That covers the vast majority of automatic gates installed in Dallas. If you know your brand, tell the person on the phone and we’ll confirm parts availability before dispatch.
What does your guarantee cover?
Every repair carries a written guarantee good for a full year from the date of service. If the same repair fails within that window, the second visit is free. That’s the 365-Day Done Right Promise, and it’s written on every job. Not a verbal assurance. A written guarantee you keep.
Do you give free estimates for automatic gate repair?
Yes. The diagnostic visit and written estimate are free. You approve the price before any work begins, and that price is fixed. Call (940) 531-9746 to schedule an arrival window.
Why is my automatic gate opening on its own?
Random opening is almost always a failing loop detector, radio interference from a nearby transmitter, or a shorted control board input. In Dallas neighborhoods with dense RF traffic from security systems and municipal transmitters, interference is more common than homeowners expect. We test each input systematically to isolate the signal source before replacing anything. If your gate is opening on its own, it means your property is not secure, so call us and we’ll get it diagnosed today.
Why Dallas Homeowners Call Carver Gate Repair
Automatic gate work is a specific trade. It sits between electrical, mechanical, and low-voltage systems, and a generalist contractor usually lacks the depth to diagnose a BFT control board fault or a Viking operator that trips its thermal overload. We’ve trained on nine major brands and we stock parts for the failures we see most in Dallas: storm-damaged boards, heat-stressed capacitors, and and Gate Realignment from clay soil movement.
Every Carver technician is background-checked and uniformed. You know who’s at your gate before you open it. Every job gets a written price before work starts. Every repair gets a written full-year guarantee. And when you call, a live person answers at any hour. That’s how a gate company should operate. That’s The Garrison Standard, and it’s been that way since 2008.
If your automatic gate is misbehaving, call (940) 531-9746 now. We’ll answer. We’ll diagnose. We’ll hand you a written price and fix it right.
Written by Lonnie Burke, Owner at Carver Gate Repair Dallas, serving Dallas.