Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Motor Repair Across Dallas
Gate motor repair in Dallas typically runs $180 to $340 for common failures like limit switch replacement, capacitor swaps, and control board repairs. Full motor replacement on a swing or slide operator usually lands between $650 and $1,400, parts included. If your gate stopped mid-cycle on a Preston Hollow driveway or your Highland Park entrance is stuck open at midnight, our crew knows exactly which streets we’re turning down and how fast we can get there. Call (940) 531-9746 and a live person answers, day or night.
Dallas’s heavy clay soil expands and contracts with every rain and dry spell, and that matters more than most homeowners expect. Posts shift out of plumb. Gates bind. Operators strain against steel that no longer hangs square. That’s the repair we do most often across this city, and it’s a repair that requires understanding Dallas dirt, Dallas heat, and Dallas gate hardware, all three at once.
Lonnie Burke runs our Dallas crew to The Garrison Standard: written prices before any work starts, background-checked technicians in uniform, and a 365-Day Done Right Promise on every repair, in writing, good for a full year.
Why Carver Gate Repair Dallas Is Dallas’s Preferred Gate Motor Repair Company
We work on gates all over Dallas, from the wide ranch entrances off Preston Road and Inwood Road to the gated estates in Preston Hollow and the shaded lots across North Dallas. That local range matters. A gate off Royal Lane built in the 1980s behaves differently than a new steel slide gate in a Mesquite subdivision, and our technicians know the difference before they arrive.
Dallas homeowners have told us the same stories for years: a technician shows up three days late, quotes $400 by phone, then writes a final invoice for $900. That doesn’t happen here. Every job gets a written price before the work begins. If the repair fails within a year, we return free, no charge and no argument. Lonnie Burke has built the Dallas crew around that simple code.
We dispatch to Dallas throughout the day and answer the phone around the clock. All calls go to a live person, including weekends and holidays. Dispatch and scheduling for our Dallas work are coordinated from the brand’s Dallas-Fort Worth office, so the crew you get is local, not routed from another state.
Part of the Garrison Partners family, Carver Gate Repair has operated to The Garrison Standard since 2008. The repair team on your gate is trained on nine major motor brands and carries the parts that Dallas gates actually fail on.
Styles & brands we work with
Gate Remote Control in Dallas
Gate Remote Control problems in Dallas are often tied to heat and age more than the remote itself. Dallas’s summer afternoons push 100°F, and receivers mounted in direct sun on steel posts can drift off frequency or fail entirely. The job usually involves testing the remote’s signal, checking the receiver antenna, reprogramming or replacing the receiver board, and syncing all remotes and keypads to the new signal.
A single remote replacement in Dallas runs $45 to $85. A receiver board replacement, which is common when the remote works at close range but not from the street, runs $150 to $280. A full receiver and remote kit, reprogrammed and tested, typically costs $220 to $380. We quote the exact price in writing before opening any housing.
Heat-Damaged Receiver Boards
The receiver is the component that hears the remote. In Dallas, we see receiver boards that have cooked in metal control boxes for years. The capacitors dry out first, then the range shortens. You’ll notice you have to press the remote twice or drive almost to the gate before it responds. That’s a board, not a battery.
Multi-Remote Programming
When a homeowner replaces a remote, the old one rarely gets deleted from the system. Over years, the receiver holds a string of old codes. We clear the memory, add the remotes you actually use, and test each one from the street and from inside a vehicle. The job takes about an hour and usually runs under $200 in Dallas.
Gate Keypad in Dallas
Gate Keypad failures in Dallas follow a pattern: the keypad face cracks from years of direct sun, water gets inside, and the membrane buttons stop registering. It’s worst on west-facing gates where the afternoon sun beats on the keypad for hours. The repair includes testing the keypad wiring, replacing the keypad or its internal membrane, and reprogramming entry codes. We also check the loop detector at the same time, because a dead keypad and a dead loop get misdiagnosed for each other constantly.
A basic keypad replacement in Dallas runs $120 to $230, installed and programmed. A wired keypad with a metal housing, common on estate gates, runs $200 to $350. Wireless keypads that can be programmed with multiple codes run $150 to $280. The written quote covers everything, no add-ons at the end.
Sun-Cracked Housings
The keypad housing on a Dallas gate takes direct sun for six hours a day, six months a year. Plastic housings crack along the corner screws, and once water enters, the circuit trace corrodes. We replace the keypad with a metal-housed unit when the gate is exposed and the budget allows, because plastic just repeats the failure cycle.
Replacing Wired Keypads on Old Systems
Older Dallas homes with 1990s and early 2000s gate systems often have wired keypads meant to pair only with that era’s receiver. When the keypad dies, we retrofit a universal wired keypad and re-terminate the conductors at the control board. It works with the existing operator. The cost stays around $150 to $300 in Dallas, and you keep the original wiring instead of trenching new line.
Trusted Brands We Service in Dallas
Our Dallas technicians carry parts for DoorKing, LiftMaster, and Mighty Mule as a baseline, plus repair kits for Linear, FAAC, BFT, Viking, Ghost Controls, and Elite. We stock the common failure parts locally in the Dallas-Fort Worth office, which means a DoorKing control board or a LiftMaster limit switch doesn’t have to ship from California. If your vintage 1990s Linear swing operator is dying on a Preston Hollow gate, we have the retrofit parts on hand to move you to a Viking or FAAC swing-arm unit without waiting on freight.
Common Gate Motor Repair Problems We See in Dallas Homes
- Clay soil heaving throws gate posts out of plumb. Dallas’s expansive clay swells after rain and contracts in drought. The post leans, the swing gate binds at the latch, and the operator bogs down until it trips its internal breaker. The fix is post re-setting or hinge re-shimming before the motor burns out.
- Decade-old linear actuators overheat and seize in summer. Dallas routinely hits 100°F from June through September. Linear actuator motors from the 1990s and early 2000s were not built for that sustained heat load. They seize mid-cycle, usually on weekday afternoons when the gate has already cycled a dozen times.
- Undersized residential operators on heavy steel estate gates. Preston Hollow and Highland Park have many ornamental steel gates spanning 16 to 22 feet. A residential swing operator rated for 600 pounds can’t carry that panel for more than a few years. The gears strip, and the gate starts swinging in the wind because the motor can’t hold position.
- Solar panel degradation on rural Dallas County entrances. Long driveways south and east of Dallas, toward Lancaster and Mesquite, often use solar-powered gate openers because running conduit to the road is impractical. The panels degrade in the heat, and the batteries stop holding charge. We replace the array and battery bank, then test the system through several open-close cycles.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Motor Repair in Dallas, TX
Gate motor repair in Dallas starts around $120 for diagnosis and small mechanical repairs, like hinge resets or a photo-eye realignment. A control board replacement for a DoorKing or LiftMaster unit runs $280 to $500. Swing arm operator replacement, the most common full-motor job on Dallas estate gates, runs $850 to $1,600 depending on gate weight and length. Slide gate operators for wide ranch entrances run $1,200 to $2,200, installed.
The factors that move Dallas pricing are gate weight, gate length, operator type, and whether posts need concrete work due to clay soil shifting. A gate that’s square and level is a two-hour motor swap. A gate with a leaning post is a half-day job. We tell you which one you have and quote it in writing before any work begins.
Call (940) 531-9746 for a free estimate. The number we quote is the number you pay, agreed before we open the control box.
We Also Serve Cities Near Dallas
Our Dallas crews also cover Dallas suburbs and nearby communities. We regularly run service calls to Irving, Mesquite, Lancaster, and Carrollton with the same written-price guarantee and 365-Day Done Right Promise. If your gate is down in any of these areas, the same live-answer phone line handles the dispatch. Our Gate Motor Repair team covers the full metro.
Serving Dallas, TX - Our Local Coverage Area
We’re based in the Dallas area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Motor Repair in Dallas
Dallas sits on expansive clay soil that swells when wet. After heavy rain, the soil around your gate posts expands and pushes the posts slightly out of plumb. The gate then hangs crooked, drags on the ground or catches at the latch, and the motor strains against the added friction. The motor is not the root problem; the post movement is. A Dallas technician checks the post alignment and hinge position first, then re-squares the gate and re-tests the operator. Expect that job to run $150 to $300. Call (940) 531-9746 to get a written quote.
Yes. The 1990s Linear actuator is still on countless Dallas gates, and it fails in the same way every summer: the internal thermal switch trips, the motor seizes, and the gate stops mid-cycle. We replace the Linear unit with a modern swing-arm operator, typically Viking or FAAC, rated for continuous summer operation. We also reinforce the hinge post while we’re in there, because the post is usually the second failure point on those old installations. A full retrofit in Dallas runs $850 to $1,500. The quote is written before we start.
If the gate spans more than 14 feet or the panel is solid steel or iron, yes. Wide ranch gates on Dallas County acreage weigh more than standard residential operators can handle, and the gears strip within a few years. A heavy-duty swing or slide operator sized for the gate’s weight and length lasts longer and holds position in wind. The conversation starts with measuring the gate and weighing the panel, then matching the operator to that spec. That service call runs $120 to $180 to assess, and we credit it toward the installation.
It means the battery bank is failing or the panel is undersized for the gate’s daily cycles. Dallas gets enough sun to run a solar gate opener, but older panels degrade in the Texas heat and lose output. When the battery can’t recharge fully, the gate works after several sunny days and dies after two cloudy ones. We replace the panel and battery bank together, and the typical cost in Dallas runs $400 to $800. Ask for a written quote at (940) 531-9746.
UL 325 is the federal standard for automatic gate safety, and it requires monitored photocells on any gate installed after 2001. A Dallas technician can test whether your photocells are monitored or non-monitored, check the beam alignment, and confirm the entrapment protection is functioning. If the system is older and lacks monitored cells, we add them as part of a control board update, which runs $300 to $550 in Dallas. This is not an upsell; it’s a safety requirement on any automatic gate.
Contact Carver Gate Repair in Dallas
We were called to a ranch-style property off Preston Road in Preston Hollow where a 1990s-era Linear swing gate operator had seized mid-afternoon during a 102°F heat wave. Our crew replaced it with a modern Viking swing-arm operator on a reinforced hinge post, then re-squared the gate and adjusted the safety photocells. The system now cycles smoothly even in peak summer heat. That’s the standard we hold on every Dallas job.
If your gate motor is failing, making noise, or just stopped, call (940) 531-9746. A live person answers, we schedule a clear arrival window, and the price is written down before any tool touches your gate. Free estimates, a full-year written guarantee, and a crew that shows up squared away.
Written by Lonnie Burke, Owner at Carver Gate Repair Dallas, operating to The Garrison Standard since 2008.